18-Outlet Vertical Networked Power Controller and Conditioner with Surge Protection and Metering
Model: PC-350V-18
Part #: 6511512
The PC-350V-18 is a vertical rack-mountable power controller designed to occupy no rack space (zero RU). It provides 120V AC power distribution, switching, surge protection, noise filtering, and energy monitoring for Crestron® control systems, AV systems, computers, and other equipment. All 18 individually-switched outlets are protected and monitored, including 12 outlets with EMI and RFI noise filtering. Ping monitoring and power cycle scheduling are adjustable to ensure connected devices are always operational. Power cycle delays and sequencing are adjustable to ensure a system powers up reliably every time. The switched outlets are also individually controllable via a control system to enable independent switching of devices, load-shedding, and other custom power control functionality.
Line voltage, current, power, and energy usage monitoring at each outlet is possible for troubleshooting and to prevent device failures. An external temperature sensor PC-TS can be purchased separately to monitor temperature within the equipment rack or room. Network connectivity allows for setup and operation using the web UI, with extensive custom control and monitoring capabilities enabled through integration with Crestron Home™ OS, the XiO Cloud® service , and Domotz™ solution.1 The PC-350V-18 can also be integrated with a custom-programmed Crestron control system via SIMPL programming software.
- Warranty - Yes
- Spec Sheet available - Yes
- Operating Temperature (Maximum): 104 F
- Operating Temperature (Minimum): 32 F
- Certifications: FCC, IC
- Number of Outlets: 18
- Surge Energy Rating: 3640 Joules
- UL Rated: Yes
- AC Voltage: 120 Volts
- Current Draw: 12 Amps
- Depth: 2.60 in
- Height: 48.10 in
- Width: 1.73 in
- Product Weight: 11.80 lbs
- Power Conditioner:
•Maximum Output Current, Total: 12A at 120VAC
•Maximum Output Current, Per Outlet: 12A at 120VAC (subject to a maximum total output current of 12A for all outlets combined)
•Filtration (Outlet 7-12): -1.9 dB at 100 kHz, -25 dB at 300 kHz, -39 dB at 500 kHz with 50 Ohm load
•Surge Protection Modes: Line-Ground, Line-Neutral, Neutral-Ground
•Surge Protection Shutoff: Shuts off outlets if surge protection is compromised
•Joule Rating: 3640 Joules
•Clamping Voltage: 600V
•Clamping Time: 1 ns
•Wiring Fault Detection: Shuts off outlets if the following wiring faults are detected at the input: Reversed polarity, Missing ground wire
•Voltage Sensing Range: 90 to 145V rms ±1%, measured at input
•Current Sensing Range: 0.1 to 12A rms ±1% when load > 1A, measured per outlet
•Under Voltage Cutoff: Adjustable 90 to 100V, shuts off outlets if input drops below set value
•Over Voltage Cutoff: Adjustable 130 to 145V, shuts off rear outlets if input exceeds set value
•Cycle Delay Adjustment: 5 to 300 seconds, adjustable per outlet
•Startup Delay Adjustment: 1 to 10 seconds, adjustable per outlet - COMMUNICATIONS:
•Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, TCP/IP, UDP/IP, CIP, DHCP, SSL, TLS, SNMP, web server, web UI setup and control, Crestron control system integration, XiO Cloud monitoring - Connectors:
•120V~ 12A 60Hz: Detachable 9.8 ft (3 m) grounded AC power cord with NEMA 5-15P plug, line power input
•OUTLET 1 -18: (18) NEMA 5-15R AC power outlets; Individually-switched 120VAC power outlets; Adjustable power cycle delay per outlet; Adjustable startup delay per outlet; Remote switchable per outlet
•TEMP: (1) 2-pin 3.5 mm detachable terminal block; Connection for external temperature sensor (not included)
•LAN: (1) 8-pin RJ45 jack; 10Base-T/100Base-TX Ethernet port - Controls and Indicators:
•PWR: (1) Bi-color green/amber LED, indicates line power is present and: illuminates amber while booting, illuminates green when the device is operating normally, turns amber if the outlets have been shut off due to a fault condition, blinks in amber during the factory reset process, blinks in green when the "Identify" search process is initiated for the unit in the Crestron Home app
•FAULT: (1) Red LED, indicates any of the following fault conditions:, surge protection is compromised, line and neutral are reversed, no ground is detected
•PROTECT: (1) Green LED, indicates surge protection is fully functional
•SHUTDOWN: (1) Amber LED, indicates power to outlets is shut off due to any of the of the following fault conditions: overvoltage, undervoltage, overcurrent, line input miswire, missing ground, compromised surge protection fault condition
•HW-R: (1) Recessed pushbutton, initiates a hardware reset of the internal CPU (does not affect outlets)
•THERMAL BREAKER: (1) Disconnects power to all outlets in case of an overload condition, press to reset after overload condition is resolved
•LAN: (2) LEDs, green LED indicates Ethernet link status, amber LED indicates Ethernet activity
•Per Outlet Indicator: (1) Green LED: Illuminates when outlet is turned on, blinks when the "Identify" search process is initiated for the outlet in the Crestron Home app - Humidity: 10% to 90% RH (non-condensing)
- Construction:
•Chassis: Metal, black finish
•Mounting: 0 RU vertically rack-mounted (mounting brackets included)
OPTECH
144 Stafford Court
Williamsburg, VA 23185
USA
(800) 868-3282
https://www.optech.net/